lcd/ST7565R.c

/**
 * \file ST7565R.c
 * \brief Functions relating to ST7565R.
 * \author Andy Gock
 * \see glcd.h
 */ 

#include "ST7565R.h"
#include "glcd_spi.h"

void glcd_command(uint8_t c)
{
	GLCD_A0_LOW();
	glcd_spi_write(c);	
}

void glcd_data(uint8_t c)
{
	GLCD_A0_HIGH();
	glcd_spi_write(c);	
}

void glcd_set_contrast(uint8_t val) {
	/* Can set a 6-bit value (0 to 63)  */

	/* Must send this command byte before setting the contrast */
	glcd_command(0x81);
	
	/* Set the contrat value ("electronic volumne register") */
	if (val > 63) {
		glcd_command(63);
	} else {
		glcd_command(val);
	}
	return;
}

void glcd_power_down(void)
{
	/* Command sequence as in ST7565 datasheet */
	glcd_command(0xac);	// Static indicator off
	glcd_command(0x00);	// Static indicator register, not blinking
	glcd_command(0xae); // Display OFF
	glcd_command(0xa5); // Display all points ON

	/* Display is now in sleep mode */
}

void glcd_power_up(void)
{
	glcd_command(0xa4); // Display all points OFF
	glcd_command(0xad);	// Static indicator ON
	glcd_command(0x00);	// Static indicator register, not Blinking
	glcd_command(0xaf);

	return;
}

void glcd_set_y_address(uint8_t y)
{
	glcd_command(ST7565R_PAGE_ADDRESS_SET | (0x0F & y)); /* 0x0F = 0b00001111 */
}

void glcd_set_x_address(uint8_t x)
{
	glcd_set_column_upper(x);
	glcd_set_column_lower(x);	
}

void glcd_all_on(void)
{
	glcd_command(ST7565R_DISPLAY_ALL_ON);
}

void glcd_normal(void)
{
	glcd_command(ST7565R_DISPLAY_NORMAL);
}

void glcd_set_column_upper(uint8_t addr)
{
	glcd_command(ST7565R_COLUMN_ADDRESS_SET_UPPER | (addr >> 4));
}

void glcd_set_column_lower(uint8_t addr)
{
	glcd_command(ST7565R_COLUMN_ADDRESS_SET_LOWER | (0x0f & addr));
}

void glcd_set_start_line(uint8_t addr)
{
	glcd_command( ST7565R_SET_START_LINE | (0x3F & addr)); /* 0x3F == 0b00111111 */
}

/** Clear the display immediately, does not buffer */
void glcd_clear_now(void)
{
	uint8_t page;
	for (page = 0; page < GLCD_NUMBER_OF_BANKS1; page++) {
		uint8_t col;
		glcd_set_y_address(page);
		glcd_set_x_address(0);
		for (col = 0; col < GLCD_NUMBER_OF_COLS1; col++) {
			glcd_data(0);
		}			
	}
}

void glcd_pattern(void)
{
	uint8_t page;
	for (page = 0; page < GLCD_NUMBER_OF_BANKS1; page++) {
		uint8_t col;
		glcd_set_y_address(page);
		glcd_set_x_address(0);
		for (col = 0; col < GLCD_NUMBER_OF_COLS1; col++) {
			glcd_data( (col / 8 + 2) % 2 == 1 ? 0xff : 0x00 );
		}			
	}
}


#define GLCD_INIT_NHD_C12864WC_FSW_FBW_3V3_M
uint8_t contrast = 33;
void glcd_ST7565R_init(void) {
	
#if defined(GLCD_INIT_NHD_C12832A1Z_FSW_FBW_3V3)

	/* Init sequence based on datasheet example code for NHD-C12832A1Z-FSW-FBW-3V3 */
	/* Datasheet says max SCK frequency 20MHz for this LCD */
	/* We use "reverse direction" for common output mode, as opposed to datasheet specifying "normal direction" */

	glcd_command(0xa0); /* ADC select in normal mode */
	glcd_command(0xae); /* Display OFF */
	glcd_command(0xc8); /* Common output mode select: reverse direction (last 3 bits are ignored) */
	glcd_command(0xa2); /* LCD bias set at 1/9 */
	glcd_command(0x2f); /* Power control set to operating mode: 7 */
	glcd_command(0x21); /* Internal resistor ratio, set to: 1 */
	glcd_set_contrast(40); /* Set contrast, value experimentally determined, can set to 6-bit value, 0 to 63 */
	glcd_command(0xaf); /* Display on */

#elif defined(GLCD_INIT_NHD_C12864A1Z_FSW_FBW_HTT)

	/* Init sequence based on datasheet example code for NHD-C12864A1Z-FSW-FBW-HTT */
	/* Datasheet says max SCK frequency 2.5MHz for this LCD */
	/* We use "reverse direction" for common output mode, as opposed to datasheet specifying "normal direction" */

	glcd_command(0xa0); /* ADC select in normal mode */
	glcd_command(0xae); /* Display OFF */
	glcd_command(0xc8); /* Common output mode select: reverse direction (last 3 bits are ignored) */
	glcd_command(0xa2); /* LCD bias set at 1/9 */
	glcd_command(0x2f); /* Power control set to operating mode: 7 */
	glcd_command(0x26); /* Internal resistor ratio, set to: 6 */
	glcd_set_contrast(30); /* Set contrast, value experimentally determined */
	glcd_command(0xaf); /* Display on */

#elif defined(GLCD_INIT_NHD_C12864WC_FSW_FBW_3V3_M)

	/* Init sequence for NHD-C12864WC-FSW-FBW-3V3-M */

	glcd_command(ST7565R_RESET); /* Internal reset */
	glcd_command(0xa2); /* 1/9 bias */
	glcd_command(0xa0); /* ADC select, normal */
	glcd_command(0xc8); /* Com output reverse */
	glcd_command(0xa4); /* Display all points normal */
	glcd_command(0x40); /* Display start line set */
	glcd_command(0x25); /* Internal resistor ratio */
	glcd_set_contrast(contrast); /* Set contrast value, experimentally determined, value 0 to 63 */
	glcd_command(0x2f); /* Power controller set */
	glcd_command(0xaf); /* Display on */
	
#elif defined(GLCD_INIT_ZOLEN_12864_FFSSWE_NAA)
	/* Init sequence for Zolen 128x64 module with
	 * size 40x35mm. Chip ST7567 */

	glcd_command(0xa0); /* ADC select in normal mode */
	glcd_command(0xae); /* Display OFF */
	glcd_command(0xc8); /* Common output mode select: reverse direction (last 3 bits are ignored) */
	glcd_command(0xa3); /* LCD bias set at 1/9 */
	glcd_command(0x2f); /* Power control set to operating mode: 7 */
	glcd_command(0x24); /* Internal resistor ratio, set to: 6 */
	glcd_set_contrast(45); /* Set contrast, value experimentally determined, value 0 to 63 */
	glcd_command(0xaf); /* Display on */
    
#elif defined(GLCD_MY)

	glcd_command(0xa2); /* 1/9 bias */
	glcd_command(0xa0); /* Select SEG Normal Direction */
	glcd_command(0xc0); /* Select COM Normal Direction */
	glcd_command(0x24); /* Select Regulation Ration=5.0 */
    glcd_command(0x81); /* Set EV Command */
    glcd_command(0x20); /* Set EV Command */
	glcd_command(0x2c); /* Power controller set */
	glcd_command(0x2e); /* Power controller set */
	glcd_command(0x2f); /* Power controller set */
	glcd_command(0xaf); /* Display on */    
#else

	/* Default init sequence */
	/* Currently just set the same as GLCD_INIT_NHD_C12864A1Z_FSW_FBW_HTT */

	glcd_command(0xa0); /* ADC select in normal mode */
	glcd_command(0xae); /* Display OFF */
	glcd_command(0xc8); /* Common output mode select: reverse direction (last 3 bits are ignored) */
	glcd_command(0xa2); /* LCD bias set at 1/9 */
	glcd_command(0x2f); /* Power control set to operating mode: 7 */
	glcd_command(0x26); /* Internal resistor ratio, set to: 6 */
	glcd_set_contrast(20); /* Set contrast, value experimentally determined, value 0 to 63 */
	glcd_command(0xaf); /* Display on */

#endif

}